Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
03/06/07 20:01
Read: times


 		 #134419 - baud rate
Responding to: ???'s previous message
I used to get it wrong the first time, but, fortunately no more

keil baudrate calculator

http://www.keil.com/c51/baudrate.asp

Erik

List of 72 messages in thread
TopicAuthorDate
Serial Communication Related Problem            01/01/70 00:00      
   partial answers            01/01/70 00:00      
      Oh yeah, i forgot about that            01/01/70 00:00      
   FIRST, THEN, THEN, THEN            01/01/70 00:00      
      A little bit of sarcasm as usual but often helpful            01/01/70 00:00      
         Proper baud rate...            01/01/70 00:00      
            baud rate            01/01/70 00:00      
               calculator            01/01/70 00:00      
            modem is autobauding            01/01/70 00:00      
               Noted            01/01/70 00:00      
   Some answers            01/01/70 00:00      
      Thanks for a patience reply            01/01/70 00:00      
   Nothing to add, but ...            01/01/70 00:00      
      i second(ed) that motion            01/01/70 00:00      
         My location profile?            01/01/70 00:00      
            with this known, it would do no good ...            01/01/70 00:00      
               Radio Shack            01/01/70 00:00      
                  Even so            01/01/70 00:00      
                     I can buy it from the local electronic shop            01/01/70 00:00      
            Sarcasm            01/01/70 00:00      
               I agree            01/01/70 00:00      
      Thanks for understanding and recommendation! - NT            01/01/70 00:00      
      More info            01/01/70 00:00      
         you need to understand the parameters.            01/01/70 00:00      
            "more valid" evidently means invalid            01/01/70 00:00      
            not quite            01/01/70 00:00      
               What a wonderful example that when total crap is s            01/01/70 00:00      
                  lesson            01/01/70 00:00      
            No, it doesn't            01/01/70 00:00      
   TxD pin to TxD pin?            01/01/70 00:00      
      dte-dce-dce-dte            01/01/70 00:00      
         Noted! Thanks!            01/01/70 00:00      
            same request question            01/01/70 00:00      
      Meaning of "Transmit"            01/01/70 00:00      
   same request question 2            01/01/70 00:00      
   Initial command sending code; help me take a look!            01/01/70 00:00      
      Make it simple for yourself            01/01/70 00:00      
         Why the need of circular buffer? Receiving?            01/01/70 00:00      
            polling versus interrupt            01/01/70 00:00      
               Check OK string at RXD or DCD at interupt?            01/01/70 00:00      
                  no good            01/01/70 00:00      
                     Voice mode only! No data communication.            01/01/70 00:00      
                        you are missing the basics            01/01/70 00:00      
                           NO carrier sent after DCD didn't found            01/01/70 00:00      
                              I do not agree            01/01/70 00:00      
                                 Interupt DCD signal for clear transmission            01/01/70 00:00      
                        For Voice Dialling            01/01/70 00:00      
                           and by the way            01/01/70 00:00      
                           Sorry for multiposting            01/01/70 00:00      
                           The ";" works but...            01/01/70 00:00      
                              ";" to return to idle state            01/01/70 00:00      
                              +++ with 3 seconds no modem activity            01/01/70 00:00      
                                 +++ escape sequence            01/01/70 00:00      
                                    Monkey See. Monkey Do.            01/01/70 00:00      
                                       Now monkey also understand?            01/01/70 00:00      
                                 Are you mistaken?            01/01/70 00:00      
                                    I think so            01/01/70 00:00      
            Circular buffers            01/01/70 00:00      
               Initial code for receiving modem response            01/01/70 00:00      
                  don't fiddle with the timer, let it run            01/01/70 00:00      
                     Understood, will run TR1 in global init, thx! - NT            01/01/70 00:00      
                  check this out, Eugene...            01/01/70 00:00      
                     Ah! Didn't know that! Thanks! -NT            01/01/70 00:00      
                     Code; modem commands & responses            01/01/70 00:00      
   V.250 (formerly V.25-ter) - get it free!            01/01/70 00:00      
   code,modem command and response            01/01/70 00:00      
   system froze when connected to hyperterminal            01/01/70 00:00      
      Your code...            01/01/70 00:00      
         It should not be a hardware problem since..            01/01/70 00:00      
            Not necessarily            01/01/70 00:00      
      Just taking a stab at it...            01/01/70 00:00      
         two 'ugly' guesses            01/01/70 00:00      

Back to Subject List